Repair cost
GE gas dryer igniter and valve repair cost
What gas dryer igniter and valve repair costs on a GE in South Florida, from $195, and what moves that number. No final price is published anywhere on this site: the figure is confirmed on site after the diagnostic and agreed in writing before anything is opened.
- From $95 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
The short version
Where this figure comes from
A starting point for built-in appliances in South Florida, published so the number is not a mystery until somebody is standing in your kitchen.
Starts at
from $195
After a diagnostic from $95, which comes off the bill when you go ahead with the work.
or call (305) 306-2503
It is not
A quote for your unit
Exact cost
Confirmed after the on-site diagnostic
Warranty
On the labor we performed
What moves it
Why two of the same job cost different amounts
These apply at the same time and in both directions. Which of them is true of your kitchen is what the on-site diagnostic settles.
-
Where the ignition sequence stops
Glow, light, sustain. Which stage fails names the part, and it takes one cycle to see.
-
The gas test on completion
Every gas job here ends with a leak test on the connection, which is part of the figure and not an option.
-
Which of the four badges it carries
GE, GE Profile, Café and Hotpoint share most of their engineering, so the part is often the same one — but not always the same price, and a component discontinued under one name is frequently current under another. That works in your favor more often than against it on an older machine.
-
How old the serial says it is
GE's serial number carries a two-letter date code, a letter for the month and a letter for the year, so the age of the appliance is known before anybody quotes anything. It is what decides whether a repair is an investment or a postponement, and we would rather have that conversation at the start.
-
Whether it is built in
A freestanding appliance rolls out. A built-in, a stacked wall oven or an over-the-range microwave is fixed into the kitchen, and the work is planned around the cabinetry. On this make most of the catalog is freestanding, which is why these figures sit below the built-in brands' in this fleet.
The work itself
What we actually do
The job behind the figure: what it involves, when a symptom points at it, and what we check first.
-
from $195 Gas dryer igniter and valve repair
A gas dryer that tumbles without heat is usually the igniter, the flame sensor or the valve coils, and the three fail in a sequence that is diagnosable by watching one cycle: whether the igniter glows, how long it glows, and whether the flame lights and then goes out.
- Diagnosed by watching one ignition cycle
- Igniter, sensor and coils, in that order of likelihood
- Gas work, done with the meter on it
In more detail
About GE gas dryer igniter and valve repair cost
Why this is a range and not a price
Every figure on this site is a starting point, and this one is from $195. What decides the number is which part it turns out to be and what the installation does to the time, and neither is known before somebody has looked. Publishing a firm figure without that would be guessing in public, and it is against the rules we run every site by.
What moves it on a GE specifically
Three things, and they are the reason this make sits below the built-in European brands in this market. GE is the largest appliance manufacturer in the United States by units in service, so its parts are stocked rather than ordered from a distributor — which is often the difference between one visit and two. Its four badges, GE, GE Profile, Café and Hotpoint, share most of their engineering, so a component discontinued under one is frequently current under another and older machines stay viable longer. And most of this catalog is freestanding rather than built into joinery, so the access that dominates a built-in repair usually does not apply.
The age, read off the plate before anything is quoted
GE’s serial number carries a two-letter date code — a letter for the month and a letter for the year — so we know how old the appliance is before naming a figure. That decides repair-or-replace more reliably than the symptom does: the same part is a sensible repair on a four-year-old machine and a poor one on a fourteen-year-old. Where the two are close, you get both numbers side by side.
What we do with the number
You get the scope and the figure in writing before anything is opened, and the diagnostic comes off the bill when you go ahead. If the honest answer is that the repair is not worth doing, you get that too — which costs us the job and is the only version of this advice worth having.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards
Before you book
Questions about GE gas dryer igniter and valve repair cost
It glows but never lights.
That is the classic weak igniter: it still glows but no longer draws enough current to open the safety valve. It looks like it is working and it is not.
It lights and then goes out.
That points at the flame sensor or the valve coils rather than the igniter, and it is why we watch a full cycle before naming a part.
Where we do it
Across Miami-Dade, Broward, and Palm Beach
Same terms everywhere we go: an on-site diagnostic first, the price agreed in writing, and the exact figure confirmed once we have seen the unit.
Neighborhoods people ask for by name